Gasket Kit - Engine

28th September 2004

Parts ordering number: -

For Toyota 4A-G 20v MAP aka blacktop 04111-16330

For Toyota 4A-G 20v AFM aka silvertop, there are two versions, don't know which is which: -

  1. 04112-16210

  2. 04111-16211

Any of them cost the same, which is Ringgit Malaysia (RM) 300 from: -

Bay Brothers Auto Sdn Bhd (spare parts shop)

No.2, Seksyen 8/1

Jalan Sungei Jernih

46050 Petaling Jaya

Selangor, Malaysia

Tel : +60(3)-7957-9409, 7957-9864, 7957-1589

Fax : +60(3)-7955-1178

The following pictures are taken from 04111-16211: -

List of items described by Khairul (nick = AE80typeD from www.zerotohundred.com)

Disclaimer by Khairul - just in case some mistakes were made. We claim no responsibility in the explanation of parts below. Please reference from engine repair manual.

Message from webmaster - credits due where it deserves, your name is not coming down :) hehe

  1. between intake plenum and 4 throttles

  2. between 4 throttles to engine

  3. between exhaust extractor to engine

  4. between engine head to engine block.

  1. Oil pump to engine block gasket

  2. Flywheel cover gasket (engine block)

  3. Exhaust header 4-2 section flange 'gaskets'

  4. Exhaust header 4-2 section flange 'gaskets'

  5. Engine valve cover fastening seals (3 nuts between the 4 spark plug holes)

  6. Engine valve cover fastening seals (3 nuts between the 4 spark plug holes)

  7. Engine valve cover fastening seals (3 nuts between the 4 spark plug holes)

  8. Probably water pump to engine head O-ring

  9. Probably distributor O-ring

  10. Used on the timing belt covers (Mid and bottom cover section)

  11. Used on the timing belt covers (Mid and bottom cover section)

  12. Used on the timing belt covers (Mid and bottom cover section)

  1. Gasket for water outlet at the exhaust no.4

  2. Gasket for water outlet at intake no.1 (under throttle 1)

  3. Gasket for water routing on the engine head's side of cylinder 4

  4. Gasket for engine oil sump to pump's intake pipe & sift (inside the block)

  5. unknown

  6. unknown

  7. unknown

  8. unknown

  9. 8 units of exhaust valve guide seal

  1. Camshaft oil seal

  2. Flywheel oil seal

  3. Spark plug 'tunnel' seal (against engine valve cover)

  4. Spark plug 'tunnel' seal (against engine valve cover)

  5. Spark plug 'tunnel' seal (against engine valve cover)

  6. Spark plug 'tunnel' seal (against engine valve cover)

  7. Camshaft oil seal

  8. unknown

List of items described by Khairul (nick = AE80typeD from www.zerotohundred.com)

Disclaimer by Khairul - just in case some mistakes were made. We claim no responsibility in the explanation of parts below. Please reference from engine repair manual.

Message from webmaster - credits due where it deserves, your name is not coming down :) hehe

These I know - 12 pieces of intake valve seals.

Cam cover rubber as well as cam pulley cover rubber.

That is all. They are not the only things required for an engine overhaul. Piston rings and crank-shaft bearings as well as con-rod bearings are required. To be detailed later.

 

  1. Gasket Kit - Engine
  2. Different Gasket Kit

 

ACOUSTICS SECTION             AUDIO SECTION             CAR SECTION

HOME - Technical Website for Acoustics, Audio and Car

  Malaysia Boleh 

 

Hit Counter